Amana Dryer Parts
View Amana Dryer Parts Category
Part Number – 279816
These thermal cut-off fuse parts are used to prevent the dryer from overheating when the dryer’s high limit thermostat has failed. This OEM parts kit includes (1) thermal cut-off fuse (309 degrees) (1) high-limit thermostat of 250 degrees Fahrenheit and the jumper wire. The high limit thermostat and thermal cut-off fuse are both mounted on the clothes dryer heater housing. Common symptoms that these parts have failed are, the dryer gets too hot, takes too long to dry the laundry, no heat, will not start. Always unplug or disconnect the electrical power source to the unit before attempting to replace these parts. Please be sure to use the model number on your appliance to ensure that these are the correct parts for your particular model of clothes dryer.
Part Number – 279838
This is a genuine OEM replacement heating element that is (240V – 5400W). The part is located inside the back of the clothes dryer attached to the heater housing. If your electric dryer is not heating, you will need to test the thermal fuse first, it is located on the blower housing, if the thermal fuse is good you will need to check for loose or burnt wires or a break in the heating element coils. If the coils have a break in them, the heating element will need to be replaced with a new one. Always unplug or disconnect the electrical power source to the appliance before attempting to repair it.
Parts Number – 279570
This is a genuine OEM door catch part kit used for some gas and electric dryer models. The parts kit comes with (3) different plastic door catches and (2) metal strikes. These parts work together to keep the dryer door closed. You will need to choose the correct door catch for your particular model. The plastic catch is mounted in the dryer door and the metal strike is mounted onto the dryer door opening on the dryer. Some common symptoms that these parts have failed are, the clothes dryer will not start, shuts off in the middle of a drying cycle, door won’t stay closed.
Part Number – 349241T
These dryer drum roller parts are used to help support the drum and allows the drum to turn smoothly inside of the dryer. The most common symptoms that the drum rollers have failed are, the dryer is very noisy, the drum will not turn. Be sure and use the model number from your appliance to ensure that these are the correct parts for your particular clothes dryer model.
Part Number – WP3392519
This dryer thermal fuse is also known as the thermal cutoff fuse and the temperature fuse. The fuse is used as a safety mechanism, cutting off electricity to the dryer motor and the heating element to keep the dryer from getting too hot. Once this fuse has blown it cannot be reused. If your fuse has blown, you will need to check for blockage or lint build up in the clothes dryer vent hose or ventilation system, before installing a new thermal fuse, only to have it blow again. Please remember to unplug or disconnect the electrical power source to the clothes dryer before attempting to replace this part.
Part Number – 341241
This part is used to turn the drum located inside the clothes dryer, it is a flat belt that measures 92 1/4 inches long and 1/4 inch wide. This belt uses an idler pulley to keep tension around the dryer drum. It is a ribbed belt with (4) ribs and (3) grooves, it replaces many dryer belts used on many other models. The common symptom that this belt has failed is, the dryer motor runs but the drum will not spin. Please be sure to use the model number on your clothes dryer to ensure that these are the correct parts for your particular appliance model.
Part Number – WP694089
This dryer part is connected to the motor shaft. As the dryer motor turns the blower wheel spins with it and blows air into the clothes dryer drum and out through the exhaust vent. Note: This blower wheel has reverse threads, you will need to rotate the blower wheel clockwise to remove it from the dryer’s motor shaft. Some common symptoms that this part has failed are, the dryer is noisy, will not tumble, will not start.
Parts Number – 279311
The gas dryer igniter parts kit comes with a bracket, (2) wire nuts and the mounting screw. This parts kit can replace both flat and round igniters. The igniter is located inside of the burner assembly. Some common signs that the ignitor has failed are, the clothes dryer will not heat, takes too long to heat. Note: you will need to take extra precautions while handling this igniter, it is a very fragile part that can break very easy.
Part Number – WP3406105
Dryer door switch. This part is located in the front right top corner of the clothes dryer. You will need to lift the top of the dryer to gain access to the door switch to replace it. The most common symptom that this door switch has failed is, the dryer will not start. Please remember to always unplug or disconnect the electrical power source to the clothes dryer before attempting to replace any parts.
Part Number – WP338906
The flame sensor is used on some gas dryers as a safety device. The sensor is used to prevent high levels of gas from building up. The sensor senses heat that is emitted from the igniter and monitors if it is hot enough to ignite the gas and light the burner. Some signs that the flame sensor has failed are, the clothes dryer takes too long to heat up, the dryer has no heat. Please be sure to use the model number on your appliance when ordering this part, to ensure that this is the correct replacement part for your particular model of gas clothes dryer.
Shop best-selling replacement parts
References to the manufacturer’s name, logo and or OEM parts numbers are for identification purposes only. Cheap Appliance Parts © 2022