GE Washer Parts

GE Washing Machine Drain Hose

Part Number – WH41X10096

Drain hose.  This part is used on many top load washing machine models, the hose is black in color, measures 57 inches in length and is made of flexible plastic.  it is located on the back side of the machine and used to remove the water from the tub to the drain after each cycle.  The most common symptom that this part has failed is water leaking onto the floor during the drain cycles.

GE Top Load Washer Lid Switch Assembly

Part Number – WH12X1043

This is a genuine OEM washer lid switch parts assembly that is located beneath the top part on some top load washers, it is activated when the lid is opened or closed.  The lid switch assembly is held into place with two screws and has a quick connect electrical wire harness.  The most common signs that this lid switch has failed are, the tub will not spin, will not agitate.  Please remember to unplug the power cord before removing or replacing any parts on your appliance.

Washer Replacement Screw

Part Number – WP489069

This replacement screw is used for many parts on a clothes washer.  The part measures 1/4″ hex head #10-12×1/2″, with a slotted 1/4″ hex head.  If you have noticed squeaking noises, parts of the washer that vibrate, or rattles a screw may have come loose or became lost and will need to be replaced to repair the problem.

GE Washing Machine Drive Belt

Part Number – WH1X2026

This belt is a V-style belt that measures 29 1/2 inches long x 1/2 inch wide it is a V-style belt that tapers to a medium V-shape.  The most common signs that this belt has failed are, the washer will not agitate, tub will not spin, motor will spin freely or the smell of burnt rubber.  Always unplug or disconnect the appliance from the electrical outlet before you begin to repair it.

GE Washer Timer

Part Number – WH12X1022

This timer is responsible for controlling most functions within the washer during its various cycles.  The timer controls when certain functions begin, end and for how long they will last.  Some common signs that this part has failed are, cycle will not advance, the washer will not fill, will not pump the water out, will not shut off or run at all.  Always unplug or disconnect the electrical power source to the washer before attempting to replace this part.

GE Front Load Washer Water Inlet Valve

Part Number – WH13X10023

Genuine OEM water inlet valve.  This part is located on the back of the washer with two hoses connecting to it, the hoses lead to the water supply lines that are designated for the washer, one hot water line and one cold water line.  Note: You will need to unplug the power cord from its electrical source and make sure to turn both the hot and cold water off, before starting this repair.  The most common signs of this part failure are, the tub will not fill with water, no hot water, no cold water or water will enter the tub even when the appliance is turned off.

GE Hose Washer with Screen

Parts Number – WH1X2267

This hose washer has a fine metal screen built into it and serves as a dual-purpose part.  It serves as a washer forming a tight seal preventing water from leaking at the hose connection.  The screen is used to catch and prevent debris such as sand, silt, and hard water calcium deposits from entering the water inlet valve and causing damage to it.

Washer Pressure Switch Hose

Part Number – WH41X365

This pressure switch hose is also referred to as the air dome tube, it is made of clear flexible plastic and is used for your top load washer.  As the water level rises inside the washer tub it forces air through the air dome and up through this plastic hose to the water level control.  This puts pressure on the level control diaphragm, tripping the water level switch from empty to full which will begin the agitation cycle.  Unplug the power cord to the unit before making this repair.

GE Washing Machine Pump and Motor

Parts Number – WH23X10030

This is a genuine OEM washer drain pump and motor part assembly is located in the right front corner, at the base of the washer.  The pump is used to help drain the water from the tub after each agitate cycle and during the spin cycle. A common symptom that the pump has failed is, the washer will not drain the water out of the tub.  Helpful tip: Check both of the pump ports and the impeller for clogs or blockage before replacing the pump with a new one.

GE Washer Tub Seal

Part Number – WH02X10383

Tub main tub seal. This seal is used in the center of the washers wash tub to prevent water from leaking around the center shaft.  The most common symptom that this seal has failed is water leaking from the center of the wash tub.  Remember to unplug the electrical power cord to the appliance before you begin to replace this part.

Washer Parts

GE Parts