Kenmore Stove Parts

View Kenmore Stove Parts Category

Kenmore Stove Surface Element 8″

Part Number – WP660533

This surface coil element is used on the cooktop surface of some freestanding electric stove models.  The surface element is 2600 watts and measures 8 inches in diameter.  It has a (5) turn coil with rolled terminal ends.  If your stove has a surface element that is not working you can test the part for continuity by using a digital or analog multi-meter.  If the element shows that it has continuity, then it is good and you will need to test your stoves surface element switch and element terminal to see if they have failed.  Please always remember to unplug or disconnect the electricity dedicated to your appliance before you begin any repairs or replace any parts.  We suggest enter your model number to be certain that this is the correct part for your specific electric stove.

Kenmore Stove Bake Element

Part Number – WPW10308477

This bake element is located inside the bottom part of the oven cavity on some stove models.  The bake element has (2) flat push-in terminals.  Some common symptoms of a bad baking element are,  the element will not heat up, trips the circuit breakers when turned on or blows a fuse.  Please remember to disconnect the electricity to your stove before attempting to repair it.  Turn the breaker dedicated to the unit off or pull the fuses.  Be safe!

Touch-up Paint – White

Part Number – 72017

This touch-up paint can be used on the metal console of your white stove.  If your gas or electric stove has unsightly chips or scratches, this touch up paint will repair the damaged areas.  The paint is white in color and comes in a (6) fluid ounce bottle with a fine brush for an easy touch-up application to the exterior of your appliance.

Kenmore Stove Temperature Sensor

Part Number – WPW10181986

This sensor works in conjunction with the ovens main control board to regulate and measure the temperature inside of the oven.  If you have noticed the oven temperature in your stove is not accurate or fluctuates by 50 degrees or more, the temperature sensor is more than likely defective and will need to be replaced.  Please be sure to use your model number when searching for parts, to be sure that they are the correct replacement part for your specific stove model.

Kenmore Stove Broil Element

Part Number – W10856603

This broil element is located inside the top part of the ovens cavity and is used for broiling.  The element is often used to help preheat an oven for a faster baking time.  If your broiler element has failed to heat up, you should be able to see some kind of visual damage, such as, blistering, bubbles, burned marks, burnt or melted terminal ends.  You can test your element for continuity using an OHM meter.  You will need to be sure to disconnect the electricity to your appliance before you begin to service it.  Safety reminder: Please give your stove plenty of time to cool down before you remove or test any parts.  Some stove parts hold their heat for quite a while and can still burn you long after you have turned the unit off.

Kenmore Electric Stove Surface Element 6″

Part Number – WP660532

This surface element is used for some electric stove cooktop surfaces.  The coil element measures 6 inches in diameter and has rolled terminal ends.  If your stove has a surface element that is not heating, it can be tested for continuity using a multi-meter.  If the element shows that it has continuity, the part is good and you will need to test the element terminal and the surface element switch.  Please don’t forget to disconnect the electricity to your appliance before attempting to remove or replace any parts.

Kenmore Gas Stove Bake / Broil Igniter

Part Number – WP8054129

This part is used to ignite the ovens gas burner with it’s spark electrode.  It is the ignition device for the baking or broiler setting on your stoves oven.  The common symptom of a bad igniter is, the burner will not light.  Please remember to disconnect your appliance from its electrical power source and turn the gas off before attempting to repair it.

Kenmore Stove Thermal Fuse

Part Number – WP3196548

This thermal fuse is used as a safety device in case the oven should overheat.  The fuse will shut the oven off to prevent a fire.  Please remember to unplug or disconnect the electricity to your stove before making this repair.

Kenmore Gas Stove Safety Valve

Part Number – WPW10293048
This gas valve is used on some gas stove models with an oven to
sense a desired amount of heat.  Once it has sensed the desired
amount of heat it will open the valve to let the gas flow to the oven
burner where it will then be ignited into flame and used to bake with.
Please unplug or disconnect the electrical power source to the stove
before attempting to repair it.

Kenmore Electric Stove Surface Heating Element 6″

Part Number – WPW10345407

This heating element measures 6 inches in diameter and is used on the cook top surface of some electric slide in stove models.  It is a three turn coil element with rolled terminal ends that push in and pull out of the stoves element receptacles.  You will need to make sure to unplug or disconnect the electricity to your stove before you begin to service it.  Please be sure and use the model number on your appliance to ensure that this is the correct part for your particular model.

Appliance Category

Browse parts for major brands

Site Information

Home Page

About Us

Contact

 

Model Number Help 

Locating Your Model #

Terms & Conditions

DISCLAIMER

Shipping Information

Same Day Shipping

 

All of the parts on this site are authentic (OEM) Original Equipment Manufacturer replacement parts, unless otherwise noted in the detailed products description.

References to the manufacturer’s name, logo and or OEM part numbers are for identification purposes only.  Cheap Appliance Parts  © 2021

Top