View Washer Parts Category
Part Number – 383EER3001V
This shock absorber comes with (2) pins that are used to hold the shock absorber into place. If your front load washer shakes, vibrates and moves around these parts may need to be replaced. Be sure to use the model number to ensure that these are the correct parts for your particular washing machine model.
Part Number – WH12X1043
Lid switch assembly. This switch is located beneath the top part of the top load model washing machine, the switch is activated when the lid is opened or closed. The assembly is held into place with two screws and has a quick connect electrical wire harness. The most common signs of a broken washer lid switch are, the tub will not spin, will not agitate. Please remember to unplug the washer before you begin this repair.
Part Number – EBR64144902
This circuit control board is used to control most all of the functions within the washer. It communicates with various parts in the washing machine and activates them as needed for each wash cycle, such as, when and how long to rinse, wash, spin and drain. Please unplug your machine before attempting to make any repairs on it.
Part Number – WH13X10023
This water valve is located on the back of the washing machine with two hoses connecting to it. The hoses lead to the water supply lines that are designated for the appliance, one hot water line and one cold water line. Note: You will need to unplug the power cord from its electrical source and make sure to turn both the hot and cold water off, before starting this repair. The most common signs of a broken washer inlet valve are, the washers tub will not fill with water, no hot water, no cold water or water will enter the tub even when the washer is turned off.
Part Number – MDS47123601
This door gasket is used to form a water tight seal between the door of the washer and the tub. This part is often referred to as the door boot or washer bellow, the rubber gasket can develop a tear or rip over time and leak water onto the floor. The main cause of damage to a door seal is over loading the washing machine with laundry. Please be sure to use your model number while ordering this part. Note: These door seals can often look alike but will not fit or function on your particular front load washing machine model.
Part Number – 5859EA1004F
This drain pump is used on a top load washer model to pump the water from the tub, out through the drain hose. Helpful tip: Be sure to check the pump ports and drain hose for obstructions, clogs or kinks before replacing your pump.
Part Number – EBR67466109
The main control board is used to control most of the functions of the washer. The control board does this by communicating with other electrical parts in the washing machine and activating a certain part when it is needed during the cycles of the washer. You will want to be sure and use the model number on your machine to be certain that this is the correct part for your appliance. Note: you will need to take extra precautions while handling this control board, it is a very delicate part. Before making this repair please make sure that your machine is disconnected from its electrical power source.
Part Number – 285753A
This washer motor coupling is used for a beltless direct drive washing machine. These replacement parts are the new and improved version of the coupling, they have an added metal shaft sleeves for extra durability. The coupler is used between the washer motor and the transmission. Some signs that the motor coupling has broken are, the washing machine will fill with water and drain the water, but will not agitate or spin.
Part Number – 285751
This top load washer agitator parts kit comes with four directional cogs, also known as dog ears. The kit also comes with the agitator cam. The main symptoms that these parts have failed are, the top part of the agitator will not catch and rotate properly, the top half of the agitator should catch and ratchet in one direction when the washing machine is in the wash cycle. If you have noticed that the top part of the agitator will not agitate this parts kit should repair your broken washing machine agitator.
Part Number – WH1X2267
This hose washer has a fine metal screen built into it and serves as a duel purpose part. It serves as a washer forming a tight seal preventing water from leaking at the fill hose connections. The screen is used as a filter to catch and prevent debris such as sand, silt, and hard water calcium deposits from entering the washers water inlet valve and causing damage to it. You will want to make sure to turn the water off, that is designated for your appliance, before making this repair.
Search by Brand Name
Search by Model Series
Maytag Atlantis Top Load Washer
Maytag Bravos Top Load Washer
Maytag Cabrio Top Load Washer
Whirlpool Calypso Top Load Washer
Maytag Centennial Top Load Washer
Whirlpool Duet Front Load Washer
Whirlpool Duet HT Front Load Washer
Maytag Ensignia Top Washer
GE Profile Harmony Top Washer
Maytag Neptune Front Load Washer
Maytag Performa Front Load Washer
Whirlpool Sport Front Load Washer
LG Tromm Front Load Washer
Whirlpool Ultimate ll Top Washer
Admiral Parts | Amana Parts | Bosh Parts | Crosley Parts | Electrolux Parts | Estate Parts | Frigidaire Parts | GE Parts | Hotpoint Parts | Inglis OEM Parts | Jenn Air Parts | Kenmore Parts | LG Parts | Maytag Parts | Roper Parts | Samsung Parts | Whirlpool Parts | Dryer Parts | Dishwasher Parts | Washer Parts | Refrigerator Parts | Oven Parts | Range Parts | Stove Parts | Appliance Parts
All of the parts on this site are genuine (OEM) Original Equipment Manufacturer replacement parts, unless otherwise noted in the detailed products description.
References to the manufacturer’s name, logo and or OEM part numbers are for identification purposes only. Cheap Appliance Parts © 2021